LiveZilla Chat
BC Wholesalers Live Chat Software
Categories
Manufacturers
Currencies

Guitar Pickups

/
Displaying 28 to 36 (of 106 products)
  • Martin Feedback Buster

    Martin Feedback Buster

    Martin FBR 2 Acoustic Guitar Feedback Buster helps eliminates feedback with acoustics guitars with pickups. Great for live use. Constructed of Black Rubber, easy to install. Fits most acoustic guitars. Plugs into Sound Hole Fits Soundholes 3 7/8" to 4" Accomadates Extended Fretboards

  • Martin Thinline 332 Plus Acoustic Guitar Pickup

    Martin Thinline 332 Plus Acoustic Guitar Pickup

    The Martin 332 Plus is a complete pickup system for acoustic guitars that includes a ceramic under-the-saddle pickup and state of the art circuitry that is housed inside the shielding of the endpin jack.

  • Martin Thinline Active Guitar Jack

    Martin Thinline Active Guitar Jack

    The Martin Thinline The Active Jack will give active performance to your existing Thinline 332 pickup or any piezo or magnetic pickup without additional modification. State-of-the-art circuitry is housed in the jack's shielding cap. The Thinline Active jack will give you more than 12,000 hours of life from one 9V battery.

  • Schaller ASD Preamp with 3000 Piezo Pickup

    Schaller ASD Preamp with 3000 Piezo Pickup

    Schaller 4 Band Preamp with 747 Piezo Bridge Saddle Pickup and Prefab plastic bridge. Made in Germany. The basic concept of this piezo/preamp combination is the noisefree transmission of the natural acoustic guitar sound in its full dynamic quality. With this combination the entire tonal spectrum of the acoustic guitar, from crystal-clear melody lines to powerful chord strumming, is faithfully reproduced. This was made possible by the use of high-grade materials such as polyester capacitors, metal film resistors, noiseless ICs and studio-quality sliders, finetuned with a carefully selected pre-contour filter and musically useful EQ frequencies.

  • Schaller Dual Soundhole Pickup with 747 Under Saddle Bridge

    Schaller Dual Soundhole Pickup with 747 Under Saddle Bridge

    Piezo pickups may be crossfaded between bridge pickup and transducer pickup (standard). Comes complete with piezo volume control and a variable super high-grade condenser microphone. Made in Germany. No drilling holes - simply plug in. Installation on or inside the guitar body. Easy battery change. Effortless battery replacement and low power consumption thanks to 3-volt technology. Microphone volume control and frequency adjustment. Endpin with switch, cable and plug.

  • Schaller Dual Soundhole Pickup with Piezo 721 Transducer

    Schaller Dual Soundhole Pickup with Piezo 721 Transducer

    Piezo pickups may be crossfaded between bridge pickup and transducer pickup (standard). Comes complete with piezo volume control and a variable super high-grade condenser microphone. Made in Germany. No drilling holes - simply plug in. Installation on or inside the guitar body. Easy battery change. Effortless battery replacement and low power consumption thanks to 3-volt technology. Microphone volume control and frequency adjustment. Endpin with switch, cable and plug.

  • Schaller Flagship Piezo Preamp - 3 way Rotary Switch

    Schaller Flagship Piezo Preamp - 3 way Rotary Switch

    Flagship - Sounds you never thought possible With this new and groundbreaking Class A preamp your music has never sounded better. Clear smooth highs, soulful mids and bodacious bass combined with an impressive dynamic range of 115dB will lead your inspiration to new levels.With a true bandwidth of 1Hz to 20kHz at +/- 0 dB our state-of-the-art FlagShip circuitry provides unprecedented signal fidelity along with exceptional operational convenience.And because of FlagShip‘s leading-edge Rail to Rail technology a single 9V alcaline battery will provide you with 1.000+ hours of play time.Enjoy a self-sensing circuitry automatically switching in mono- or stereo-operation respectively by sensing which kind of chord you plugged in. In addition the FlagShip preamp offers an ultra-silent operation with a signal to noise-ratio of -115dB and a noise floor of just 20 dBV while Schaller‘s own FlagShip gold-contact 5-way Megaswitch lets you choose from a vast variety of piezo and magnetic switching-options and –combinations never seen in any preamp before.SoundInnovationPerformance    Suitable for all piezo-pickup systems    plug & play    solderfree connections5-Way Megaswitch Switching Options in Mono- and in Stereo-Mode:Mono and stereo positions 2 through 5 feature identical controls and functions allowing for a transparent layout and easy handling. Pos 1 Mono and Pos 1 Stereo feature special utility settings.Pos 1 mono: piezo raw-mode (1) / stereo: mute, silent-mode (2)Pos 2 piezo into FlagShip preampPos 3 magnetic pickups and piezo signal into FlagShip preampPos 4 magnetic pickups into FlagShip preamp (buffered)Pos 5 magnetic pickups pure and unaltered (hardwire-bypass)(1) for reference purposes use this option to hear the raw piezo signal(2) when playing live use this option for silently changing instruments3-Way rotary switch  Switching Options in Mono- and Stereo-Mode:The mono and stereo switching positions 2, 3 and 5 feature identical controls and switching functions for user-friendly layout.MONOPos 2     acoustic activePos 3     magnetic + acoustic activePos 5     magnetic bypassSTEREOPos 2     acoustic activePos 3     magnetic + acoustic activePos 5     magnetic bypassFeatures, Specifications & Benefits    Advanced class A circuitry for sweet,transparent sound    Compact, robust and perfectly shielded    Attractive and protective casing with see-through window    Original Schaller gold-contact 5-way Megaswitch for outstanding signal flow and switching options    Stereo/mono selfsensing and –adjusting circuitry (no extra switch required)    Rail to Rail energy effi ciency technology    Reverse polarity and static discharge circuit protection    Automatic power shut-off when cable is disconnected    Plug-in contacts for easy solderfree installation    1000+ hours of playtime on a single 9V alcaline battery    True 1Hz - 20kHz bandwidth at +/-0 dB    Ultra quiet -115 dB signal to noise-ratio    Input impedance: magnetic 3 megohms / piezo 1 megohm    Output impedance: 5 megohms    All parts and components 100% made in Germany    Comes complete with 5-way Megaswitch, mono-/stereo-jack, Schaller control potentiometer (22K-Ohm), wiring and plugs    Weight in gramms: 49    Size in mm: 89 x 24 x 7(all specifications subject to change without notice)Volume piezo bridge and passive pickup with variable adjustment.Supplied with a stereo jack socket. This allows the piezo and pickup signal to be separated using a stereo splitter y-cable and then connected to two different amps or channels.Caution: When a connection is made to pickups that are already live, the output signal increases automatically!A 9 volt battery can be used as a general power supply.Please note that piezo bridges are not earthed.A comprehensive instruction and installation guide with additional detailed information and illustrations are available to download on our webseite under products/product help/flagship.    Quick 10 Step Guide to FlagShip01. signal to noise ratioratio describing the level of signal to the level of background noise in dB (higher is better)02. dynamic rangemeasured gap from the loudest possible undistorted signal amplitude to the most quiet one in dB (higher is better)03. bandwidthspan between the lowest (here 1 Hz) and the highest frequency (here 20 kHz) the preamp can linearly (meaning without distortion) amplify or reproduce04. noise floorsignal created from the sum of all noise sources (lower is better)05. hardwire-bypass or true bypasspure and unaltered guitar signal by way of bypassing any form of active signal-processing06. reverse polarity protectioncircuitry protecting the electronic components from interchanging plus and minus polarity (here: protection from interchanging the +poles and -poles of the battery)07. static discharge protectioncircuitry protecting the electronic components from an electrical voltage spark or 'spike'08. piezo pickuppiezo-electrical signal created by transforming pressure/vibration into output voltage09. magnetic pickupmagnetic pickup signal is created by transforming string motion and magnetic resistance into output voltage10. buffered signalhigh impedance signal transformed into a low impedance signal, therefore unaffected by high capacitance of excessive signal-cable and/or patch-cable lengthsAnother significant benefit of switching pos 4. is the buffered signal, i.e. the conversion of the high capacity passive pickup signal into a low capacity active pickup signal. This prevents sound degradation commonly associated with running extended cable lengths or using inferiour cable qualities. Your magnetic pickup signal will remain strong, clear and detailed even on the most unfavourable conditions.(see: Quick 10 Step Guide to FlagShip) Schaller Flagship preamp – Stereo / Mono OperationFor mono and for stereo use the Flagship preamp features an advanced mono / stereo selfsensing output stage. The Flagship preamp senses whether a mono 1/4“ or a stereo 1/4“ plug is inserted and switches into the appropriate mode automatically. Not only does this prevent misuse so commonly known from mono/stereo toggle switches. It also allows for just one output jack (see stereo jack enclosed) in your guitar to operate the Flagship to its fullest potential.In mono mode the sound of the magnetic pickups is mixed with the sound of the piezo pickups within the preamp. We recommend using a regular 1/4“ plug guitar cable. Please refer to the Flagship manual for all dedicated sound options in this mode.In stereo mode the sound of the magnetic pickups and the sound of the piezo pickups are sent seperately to the stereo output jack. Please refer to the Flagship manual for all dedicated sound options in this mode.We recommend two ways for routing the signals:1. Using a stereo cable with two 1/4“ plugs for routing the magnetic and piezo signal seperately to a mixing console’s stereo input.2. Using a Y-cable with two 1/4“ mono plugs and one 1/4“ stereo plug for splitting your signal between a guitar amp for the magnetic pickups and a PA or acoustic amp for the piezo signal.The stereo and mono plugs should be connected as follows:Tip of stereo plug goes to tip of mono plug left.Ring of stereo plug goes to tip of mono plug right.Sleeve of stereo plug goes to sleeve of mono plug left.Sleeve of stereo plug goes to sleeve of mono plug right.Please note that by connecting the grounds of two amps or an amp with a PA a low-frequency ground hum may occur. This is an inherent problem caused by ground loops and in no way a fault within the Flagship preamp.

  • Schaller Flagship Piezo Preamp - 5 way Toggle Switch

    Schaller Flagship Piezo Preamp - 5 way Toggle Switch

    Flagship - Sounds you never thought possible With this new and groundbreaking Class A preamp your music has never sounded better. Clear smooth highs, soulful mids and bodacious bass combined with an impressive dynamic range of 115dB will lead your inspiration to new levels.With a true bandwidth of 1Hz to 20kHz at +/- 0 dB our state-of-the-art FlagShip circuitry provides unprecedented signal fidelity along with exceptional operational convenience.And because of FlagShip‘s leading-edge Rail to Rail technology a single 9V alcaline battery will provide you with 1.000+ hours of play time.Enjoy a self-sensing circuitry automatically switching in mono- or stereo-operation respectively by sensing which kind of chord you plugged in. In addition the FlagShip preamp offers an ultra-silent operation with a signal to noise-ratio of -115dB and a noise floor of just 20 dBV while Schaller‘s own FlagShip gold-contact 5-way Megaswitch lets you choose from a vast variety of piezo and magnetic switching-options and –combinations never seen in any preamp before.SoundInnovationPerformance    Suitable for all piezo-pickup systems    plug & play    solderfree connections5-Way Megaswitch Switching Options in Mono- and in Stereo-Mode:Mono and stereo positions 2 through 5 feature identical controls and functions allowing for a transparent layout and easy handling. Pos 1 Mono and Pos 1 Stereo feature special utility settings.Pos 1 mono: piezo raw-mode (1) / stereo: mute, silent-mode (2)Pos 2 piezo into FlagShip preampPos 3 magnetic pickups and piezo signal into FlagShip preampPos 4 magnetic pickups into FlagShip preamp (buffered)Pos 5 magnetic pickups pure and unaltered (hardwire-bypass)(1) for reference purposes use this option to hear the raw piezo signal(2) when playing live use this option for silently changing instruments3-Way rotary switch  Switching Options in Mono- and Stereo-Mode:The mono and stereo switching positions 2, 3 and 5 feature identical controls and switching functions for user-friendly layout.MONOPos 2     acoustic activePos 3     magnetic + acoustic activePos 5     magnetic bypassSTEREOPos 2     acoustic activePos 3     magnetic + acoustic activePos 5     magnetic bypassFeatures, Specifications & Benefits    Advanced class A circuitry for sweet,transparent sound    Compact, robust and perfectly shielded    Attractive and protective casing with see-through window    Original Schaller gold-contact 5-way Megaswitch for outstanding signal flow and switching options    Stereo/mono selfsensing and –adjusting circuitry (no extra switch required)    Rail to Rail energy effi ciency technology    Reverse polarity and static discharge circuit protection    Automatic power shut-off when cable is disconnected    Plug-in contacts for easy solderfree installation    1000+ hours of playtime on a single 9V alcaline battery    True 1Hz - 20kHz bandwidth at +/-0 dB    Ultra quiet -115 dB signal to noise-ratio    Input impedance: magnetic 3 megohms / piezo 1 megohm    Output impedance: 5 megohms    All parts and components 100% made in Germany    Comes complete with 5-way Megaswitch, mono-/stereo-jack, Schaller control potentiometer (22K-Ohm), wiring and plugs    Weight in gramms: 49    Size in mm: 89 x 24 x 7(all specifications subject to change without notice)Volume piezo bridge and passive pickup with variable adjustment.Supplied with a stereo jack socket. This allows the piezo and pickup signal to be separated using a stereo splitter y-cable and then connected to two different amps or channels.Caution: When a connection is made to pickups that are already live, the output signal increases automatically!A 9 volt battery can be used as a general power supply.Please note that piezo bridges are not earthed.A comprehensive instruction and installation guide with additional detailed information and illustrations are available to download on our webseite under products/product help/flagship.    Quick 10 Step Guide to FlagShip01. signal to noise ratioratio describing the level of signal to the level of background noise in dB (higher is better)02. dynamic rangemeasured gap from the loudest possible undistorted signal amplitude to the most quiet one in dB (higher is better)03. bandwidthspan between the lowest (here 1 Hz) and the highest frequency (here 20 kHz) the preamp can linearly (meaning without distortion) amplify or reproduce04. noise floorsignal created from the sum of all noise sources (lower is better)05. hardwire-bypass or true bypasspure and unaltered guitar signal by way of bypassing any form of active signal-processing06. reverse polarity protectioncircuitry protecting the electronic components from interchanging plus and minus polarity (here: protection from interchanging the +poles and -poles of the battery)07. static discharge protectioncircuitry protecting the electronic components from an electrical voltage spark or 'spike'08. piezo pickuppiezo-electrical signal created by transforming pressure/vibration into output voltage09. magnetic pickupmagnetic pickup signal is created by transforming string motion and magnetic resistance into output voltage10. buffered signalhigh impedance signal transformed into a low impedance signal, therefore unaffected by high capacitance of excessive signal-cable and/or patch-cable lengthsAnother significant benefit of switching pos 4. is the buffered signal, i.e. the conversion of the high capacity passive pickup signal into a low capacity active pickup signal. This prevents sound degradation commonly associated with running extended cable lengths or using inferiour cable qualities. Your magnetic pickup signal will remain strong, clear and detailed even on the most unfavourable conditions.(see: Quick 10 Step Guide to FlagShip) Schaller Flagship preamp – Stereo / Mono OperationFor mono and for stereo use the Flagship preamp features an advanced mono / stereo selfsensing output stage. The Flagship preamp senses whether a mono 1/4“ or a stereo 1/4“ plug is inserted and switches into the appropriate mode automatically. Not only does this prevent misuse so commonly known from mono/stereo toggle switches. It also allows for just one output jack (see stereo jack enclosed) in your guitar to operate the Flagship to its fullest potential.In mono mode the sound of the magnetic pickups is mixed with the sound of the piezo pickups within the preamp. We recommend using a regular 1/4“ plug guitar cable. Please refer to the Flagship manual for all dedicated sound options in this mode.In stereo mode the sound of the magnetic pickups and the sound of the piezo pickups are sent seperately to the stereo output jack. Please refer to the Flagship manual for all dedicated sound options in this mode.We recommend two ways for routing the signals:1. Using a stereo cable with two 1/4“ plugs for routing the magnetic and piezo signal seperately to a mixing console’s stereo input.2. Using a Y-cable with two 1/4“ mono plugs and one 1/4“ stereo plug for splitting your signal between a guitar amp for the magnetic pickups and a PA or acoustic amp for the piezo signal.The stereo and mono plugs should be connected as follows:Tip of stereo plug goes to tip of mono plug left.Ring of stereo plug goes to tip of mono plug right.Sleeve of stereo plug goes to sleeve of mono plug left.Sleeve of stereo plug goes to sleeve of mono plug right.Please note that by connecting the grounds of two amps or an amp with a PA a low-frequency ground hum may occur. This is an inherent problem caused by ground loops and in no way a fault within the Flagship preamp.

  • Schaller Humbucker 212B 2-in-1 Black

    Schaller Humbucker 212B 2-in-1 Black

    Extremely high output electric guitar pickup for bridge position, equipped with 12 adjustable pole pieces, producing a solid sustain and aggressive sound. The four-conductor cable supports various different sound options: parallel, in series, single coil, and phasing with second pick-up. Mini-switch and Allen key included.

/
Displaying 28 to 36 (of 106 products)